Use the exact same clocks with HOS and utilize low jitter clock parents.
Add back our compatibility mode and the missing timeout clock parent.
Hekate main will continue to use PLLP clock parent for all.
hekate main always runs in compatibility mode (SDR82).
This ensures speed on boot process.
Nyx will first try SDR104.
If the sd card is a sandisk U1 and fails, it will try the compatibility mode.
After that it fallbacks to lower bus speeds.
Both support 1bit mode for broken sd card readers.
Having the new error checking in the sdmmc driver, allows for all that to work.
It can now fail instead of continuing, like how HOS reacts.
Allows more kip names to be added. To use it on them you will need to dump the kips via the Dump pkg1/2 function and then sha256 to get the hash.
The name must be used as is, otherwise the name compare will fail.
Because of that, also allow unordered parsing and gluing.
Using the key `emupath` on a boot entry will load the selected emuMMC.
This can also be forced by using the correct boot cfg storage bit and writing the path at the emummc path offset. Check readme for these.
This can only be used if the emuMMC was created via Nyx. because of the raw_based and file_based files that have emuMMC info.
(emupath=emuMMC/RAW1, emupath=emuMMC/SD00, etc)
This disables low battery monitor shutdown (LBM shutdown) on boot and checks if battery is enough.
The logic is as follows:
If battery is not enough:
- If not charging and 15s pass, it will re enable LBM shutdown and power off.
- If charging, it will wait until it is charged above the limit.
Screen will auto turn off to save power. A press on Power button or a change on charger, will enable it for another 15s.
If battery is enough:
- Enables LBM shutdown and continues with the boot process.
Use key `fss0experimental=1` in a boot entry with `fss0=` defined to enable experimental content.
(Older versions of hekate will just skip any experimental content.)
Additionally disable archive bit fix tool in hekate main to shave binary size.
The archive bit fix in Nyx is the only maintained one and so the only one that should be used.
There is an edge case fixed where the whole would be freed and this would make use of a nullptr.
Additionally, remove usage of reserved names for vars and add comments on how it works.
This fixes the following case:
When force is 0 and the payload is not hekate, the function jumps to the 'is old' check.
This skips the is magic value check and only does the version check.
In case the foreign payload has a low value on that offset, it causes an overwrite which is unneeded.
Fixes a hang caused when rebooting 2 payload from L4T with old hekate in vendor partition.
L4T does not overwrite the nyx storage where the Minerva configuration is stored.
This makes new Minerva parse the wrong tables from old hekate and eventually hang the RAM, which causes an exception on BPMP.
If `fss0=` key is detected, sept will be loaded from fusee-secondary.bin instead of `sept/sept_*`.
This will negate missing sept and failed to decrypt pkg2 errors, when booting HOS, for users that forget to update sept folder.
It will now show erros for the following:
- Missing or old libsys_minerva.bso (DRAM training).
- Missing libsys_lp0.bso (LP0 sleep mode).
- Missing or old Nyx version
This is conditional:
In order to not cancel booting while trying to enter fastboot in android, the combo MUST be initiated with `VOL+` (hold) -> `VOL-` (hold)
3 users had issues with 602MHz.
This will probably bring the SoC binning compatibility to 100%.
Additionally, make it easy to change default boost frequency.
The tiny loss in perf, will be mitigated in Nyx. (It's actually even faster)
There's an increasing ammount of users that kill their batteries when forgetting their devices into AutoRCM / RCM mode.
This will now force a shutdown the moment the battery reaches 2.8V. Even if device is inside RCM mode.
Notice: We might need to increase the limit.
- Training and switch is now faster
- Compatibility checks: New Minerva does not allow old binaries. New binaries do not allow old Minerva
- MTC table is now in a safe region
- Periodic training period increased to every 250ms
- Allow reuse of unused sections that fit exactly to selected allocation size. Decreases fragmentation dramatically.
- Always allocate and align mapped memory to selected alignment. Avoids having fragmented unused maps that are not aligned.
- Use a static alignment based on BPMP and generally average cache line size. Boosts performance when MMU is used.
Allow the patch loop to end via empty source data as per original spec and error out on 0 length if source data is not null.
emuMMC force decompression patch safely avoids that.
- Allow SHA to calculate sizes > 16MB and refactor sha function
- Name various registers and magic numbers
- Fix various key access bugs
In a later commit this new design will boost verification times significantly and also allow full SHA256 hashes.
Remove patches_template.ini load.
- It has useless patches, which some times, users confuse them for "bad" patches, even though they aren't.
- No one reads on how it works and it's constantly mishandled when there's no patches.ini (which completely overrides it).
- It was not supposed to be edited.
Also release will not include it anymore.
Template will still exist for demonstrating the syntax of `patches.ini`
This commit also corrects the patches.ini encoding note as ASCII.
Tsec keys function always disabled host1x clock after running.
This interferes with display interface and disables further window frame syncing.
Display_end code already handles disable and reset of said clock.
It also fixes an ancient bug that was mitigated by removing the 5 frame sync on HOST1X_SYNC_SYNCPT_9 at channel 0:
5fd9daa364 (diff-6b0c56eab8515465d559ff0ea73a22c3L152)
By using the key `id=` with a max 7 ASCII id, hekate will search all inis automatically and pinpoint the boot entry with that id.
After that it forces a boot from this one.
