mirror of
https://github.com/CTCaer/hekate
synced 2024-09-07 08:39:00 +00:00
1596 lines
44 KiB
C
1596 lines
44 KiB
C
/*
|
|
* Enhanced USB Device (EDCI) driver for Tegra X1
|
|
*
|
|
* Copyright (c) 2019-2020 CTCaer
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms and conditions of the GNU General Public License,
|
|
* version 2, as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope it will be useful, but WITHOUT
|
|
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
|
|
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
|
|
* more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#include <string.h>
|
|
#include <stdlib.h>
|
|
|
|
#include <usb/usbd.h>
|
|
#include <usb/usb_descriptor_types.h>
|
|
#include <usb/usb_t210.h>
|
|
|
|
#include <gfx_utils.h>
|
|
#include <soc/bpmp.h>
|
|
#include <soc/clock.h>
|
|
#include <soc/fuse.h>
|
|
#include <soc/gpio.h>
|
|
#include <soc/pinmux.h>
|
|
#include <soc/pmc.h>
|
|
#include <soc/t210.h>
|
|
#include <utils/btn.h>
|
|
#include <utils/util.h>
|
|
|
|
#include <memory_map.h>
|
|
|
|
typedef enum
|
|
{
|
|
USB_HW_EP0 = 0,
|
|
USB_HW_EP1 = 1
|
|
} usb_hw_ep_t;
|
|
|
|
typedef enum
|
|
{
|
|
USB_EP_STATUS_IDLE = 0,
|
|
USB_EP_STATUS_ACTIVE = 1,
|
|
USB_EP_STATUS_ERROR = 2,
|
|
USB_EP_STATUS_NO_CONFIG = 3,
|
|
USB_EP_STATUS_STALLED = 4,
|
|
USB_EP_STATUS_DISABLED = 5
|
|
} usb_ep_status_t;
|
|
|
|
typedef enum {
|
|
USB_LOW_SPEED = 0,
|
|
USB_FULL_SPEED = 1,
|
|
USB_HIGH_SPEED = 2,
|
|
USB_SUPER_SPEED = 3,
|
|
} usb_speed_t;
|
|
|
|
typedef struct _dTD_t
|
|
{
|
|
vu32 next_dTD;
|
|
vu32 info;
|
|
vu32 pages[5];
|
|
vu32 reserved;
|
|
} dTD_t;
|
|
|
|
typedef struct _dQH_t
|
|
{
|
|
vu32 ep_capabilities;
|
|
vu32 curr_dTD_ptr;
|
|
vu32 next_dTD_ptr;
|
|
vu32 token;
|
|
vu32 buffers[5]; // hmmm.
|
|
vu32 reserved;
|
|
vu32 setup[2];
|
|
vu32 gap[4];
|
|
} dQH_t;
|
|
|
|
typedef struct _usbd_t
|
|
{
|
|
volatile dTD_t dtds[4 * 4]; // 4 dTD per endpoint.
|
|
volatile dQH_t *qhs;
|
|
int ep_configured[4];
|
|
int ep_bytes_requested[4];
|
|
} usbd_t;
|
|
|
|
typedef struct _usbd_controller_t
|
|
{
|
|
u32 port_speed;
|
|
t210_usb2d_t *regs;
|
|
usb_ctrl_setup_t control_setup;
|
|
usb_desc_t *desc;
|
|
usb_gadget_type gadget;
|
|
u8 config_num;
|
|
u8 interface_num;
|
|
u8 max_lun;
|
|
bool usb_phy_ready;
|
|
bool configuration_set;
|
|
bool max_lun_set;
|
|
bool bulk_reset_req;
|
|
bool hid_report_sent;
|
|
u32 charger_detect;
|
|
} usbd_controller_t;
|
|
|
|
extern u8 hid_report_descriptor_jc[];
|
|
extern u8 hid_report_descriptor_touch[];
|
|
extern u32 hid_report_descriptor_jc_size;
|
|
extern u32 hid_report_descriptor_touch_size;
|
|
|
|
extern usb_desc_t usb_gadget_hid_jc_descriptors;
|
|
extern usb_desc_t usb_gadget_hid_touch_descriptors;
|
|
extern usb_desc_t usb_gadget_ums_descriptors;
|
|
|
|
usbd_t *usbdaemon;
|
|
|
|
usbd_controller_t *usbd_otg;
|
|
usbd_controller_t usbd_usb_otg_controller_ctxt;
|
|
|
|
bool usb_init_done = false;
|
|
|
|
u8 *usb_ep0_ctrl_buf = (u8 *)USB_EP_CONTROL_BUF_ADDR;
|
|
|
|
static int _usbd_reset_usb_otg_phy_device_mode()
|
|
{
|
|
usbd_otg->usb_phy_ready = false;
|
|
|
|
// Clear UTMIP reset.
|
|
USB(USB1_IF_USB_SUSP_CTRL) &= ~SUSP_CTRL_UTMIP_RESET;
|
|
|
|
// Wait for PHY clock to get validated.
|
|
u32 retries = 100000; // 200ms timeout.
|
|
while (!(USB(USB1_IF_USB_SUSP_CTRL) & SUSP_CTRL_USB_PHY_CLK_VALID))
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_INIT;
|
|
usleep(1);
|
|
}
|
|
usbd_otg->usb_phy_ready = true;
|
|
|
|
// Clear all device addresses, enabled setup requests and transmit events.
|
|
usbd_otg->regs->periodiclistbase = 0;
|
|
usbd_otg->regs->endptsetupstat = usbd_otg->regs->endptsetupstat;
|
|
usbd_otg->regs->endptcomplete = usbd_otg->regs->endptcomplete;
|
|
|
|
// Stop device controller.
|
|
usbd_otg->regs->usbcmd &= ~USB2D_USBCMD_RUN;
|
|
|
|
// Set controller mode to idle.
|
|
usbd_otg->regs->usbmode &= ~USB2D_USBMODE_CM_MASK;
|
|
|
|
// Reset the controller.
|
|
usbd_otg->regs->usbcmd |= USB2D_USBCMD_RESET;
|
|
|
|
// Wait for the reset to complete.
|
|
retries = 100000; // 200ms timeout.
|
|
while (usbd_otg->regs->usbcmd & USB2D_USBCMD_RESET)
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_INIT;
|
|
usleep(1);
|
|
}
|
|
|
|
// Wait for PHY clock to get validated after reset.
|
|
retries = 100000; // 200ms timeout.
|
|
while (!(USB(USB1_IF_USB_SUSP_CTRL) & SUSP_CTRL_USB_PHY_CLK_VALID))
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_INIT;
|
|
usleep(1);
|
|
}
|
|
|
|
// Set controller to Device mode.
|
|
usbd_otg->regs->usbmode = (usbd_otg->regs->usbmode & ~USB2D_USBMODE_CM_MASK) | USB2D_USBMODE_CM_DEVICE;
|
|
|
|
// Wait for the selected mode to be enabled.
|
|
retries = 100000; // 200ms timeout.
|
|
while ((usbd_otg->regs->usbmode & USB2D_USBMODE_CM_MASK) != USB2D_USBMODE_CM_DEVICE)
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_INIT;
|
|
usleep(1);
|
|
}
|
|
|
|
// Disable all interrupts.
|
|
usbd_otg->regs->usbintr = 0;
|
|
|
|
// Set the ID pullup and disable all OTGSC interrupts.
|
|
usbd_otg->regs->otgsc = USB2D_OTGSC_USB_ID_PULLUP;
|
|
|
|
// Clear all relevant interrupt statuses.
|
|
usbd_otg->regs->usbsts =
|
|
USB2D_USBSTS_UI | USB2D_USBSTS_UEI | USB2D_USBSTS_PCI |
|
|
USB2D_USBSTS_FRI | USB2D_USBSTS_SEI | USB2D_USBSTS_AAI |
|
|
USB2D_USBSTS_URI | USB2D_USBSTS_SRI | USB2D_USBSTS_SLI;
|
|
|
|
// Disable and clear all OTGSC interrupts.
|
|
usbd_otg->regs->otgsc = USB2D_OTGSC_USB_IRQ_STS_MASK;
|
|
|
|
// Clear EP0, EP1, EP2 setup requests.
|
|
usbd_otg->regs->endptsetupstat = 7; //TODO: Shouldn't this be endptsetupstat = endptsetupstat?
|
|
|
|
// Set all interrupts to immediate.
|
|
usbd_otg->regs->usbcmd &= ~USB2D_USBCMD_ITC_MASK;
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
static void _usb_charger_detect()
|
|
{
|
|
// Charger detect init.
|
|
usbd_otg->charger_detect = 0;
|
|
bool charger_detect_enable = FUSE(FUSE_RESERVED_SW) & 0x10; // Disabled on Switch production.
|
|
if (charger_detect_enable)
|
|
{
|
|
usbd_otg->charger_detect |= 1;
|
|
// Configure detect pin.
|
|
PINMUX_AUX(PINMUX_AUX_LCD_GPIO1) &= ~(PINMUX_PARKED | PINMUX_TRISTATE | PINMUX_PULL_MASK);
|
|
gpio_config(GPIO_PORT_V, GPIO_PIN_3, GPIO_MODE_GPIO);
|
|
|
|
// Configure charger pin.
|
|
PINMUX_AUX(PINMUX_AUX_USB_VBUS_EN1) &=
|
|
~(PINMUX_INPUT_ENABLE | PINMUX_PARKED | PINMUX_TRISTATE | PINMUX_PULL_MASK);
|
|
gpio_config(GPIO_PORT_CC, GPIO_PIN_5, GPIO_MODE_GPIO);
|
|
gpio_output_enable(GPIO_PORT_CC, GPIO_PIN_5, GPIO_OUTPUT_ENABLE);
|
|
|
|
// Enable charger.
|
|
if (gpio_read(GPIO_PORT_V, GPIO_PIN_3))
|
|
{
|
|
usbd_otg->charger_detect |= 2;
|
|
gpio_write(GPIO_PORT_CC, GPIO_PIN_5, GPIO_HIGH);
|
|
usbd_otg->charger_detect |= 0x100;
|
|
USB(USB1_UTMIP_BAT_CHRG_CFG0) = BAT_CHRG_CFG0_OP_SRC_EN; // Clears UTMIP_PD_CHRG and enables charger detect.
|
|
usleep(5000);
|
|
}
|
|
}
|
|
}
|
|
|
|
static void _usb_init_phy()
|
|
{
|
|
// Configure and enable PLLU.
|
|
clock_enable_pllu();
|
|
|
|
// Enable USBD clock.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_L_SET) = BIT(CLK_L_USBD);
|
|
usleep(2);
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_L_SET) = BIT(CLK_L_USBD);
|
|
usleep(2);
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_L_CLR) = BIT(CLK_L_USBD);
|
|
usleep(2);
|
|
|
|
// Clear XUSB_PADCTL reset
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_W_CLR) = BIT(CLK_W_XUSB_PADCTL);
|
|
|
|
// Enable USB PHY and reset for programming.
|
|
u32 usb_susp_ctrl = USB(USB1_IF_USB_SUSP_CTRL);
|
|
USB(USB1_IF_USB_SUSP_CTRL) = usb_susp_ctrl | SUSP_CTRL_UTMIP_RESET;
|
|
USB(USB1_IF_USB_SUSP_CTRL) = usb_susp_ctrl | SUSP_CTRL_UTMIP_PHY_ENB | SUSP_CTRL_UTMIP_RESET;
|
|
|
|
// Enable IDDQ control by software and disable UTMIPLL IDDQ.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIPLL_HW_PWRDN_CFG0) = (CLOCK(CLK_RST_CONTROLLER_UTMIPLL_HW_PWRDN_CFG0) & 0xFFFFFFFC) | 1;
|
|
usleep(10);
|
|
|
|
// Disable crystal clock.
|
|
USB(USB1_UTMIP_MISC_CFG1) &= 0xBFFFFFFF;
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) &= 0xBFFFFFFF;
|
|
|
|
// Set B_SESS_VLD.
|
|
USB(USB1_IF_USB_PHY_VBUS_SENSORS) |= 0x1000;
|
|
USB(USB1_IF_USB_PHY_VBUS_SENSORS) |= 0x800;
|
|
|
|
// Set UTMIPLL dividers and config based on OSC and enable it to 960 MHz.
|
|
clock_enable_utmipll();
|
|
|
|
// Configure UTMIP Transceiver Cells.
|
|
u32 fuse_usb_calib = FUSE(FUSE_USB_CALIB);
|
|
USB(USB1_UTMIP_XCVR_CFG0) = (((USB(USB1_UTMIP_XCVR_CFG0) & 0xFFFFFFF0) | (fuse_usb_calib & 0xF)) & 0xFE3FFFFF) | ((fuse_usb_calib & 0x3F) << 25 >> 29 << 22);
|
|
USB(USB1_UTMIP_XCVR_CFG1) = (USB(USB1_UTMIP_XCVR_CFG1) & 0xFFC3FFFF) | ((fuse_usb_calib << 21) >> 28 << 18);
|
|
USB(USB1_UTMIP_XCVR_CFG3) = (USB(USB1_UTMIP_XCVR_CFG3) & 0xFFFFC1FF) | ((FUSE(FUSE_USB_CALIB_EXT) & 0x1F) << 9);
|
|
USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFDFFFFF;
|
|
USB(USB1_UTMIP_XCVR_CFG2) = (USB(USB1_UTMIP_XCVR_CFG2) & 0xFFFFF1FF) | 0x400;
|
|
usleep(1);
|
|
|
|
// Configure misc UTMIP.
|
|
USB(USB1_UTMIP_DEBOUNCE_CFG0) = (USB(USB1_UTMIP_DEBOUNCE_CFG0) & 0xFFFF0000) | 0xBB80;
|
|
USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFFFFC0FF) | 0x100; // when osc is 38.4KHz
|
|
|
|
//USB(USB1_UTMIP_SPARE_CFG0) &= 0xFFFFFEE7; unpatched0
|
|
USB(USB1_UTMIP_BIAS_CFG2) |= 2; //patched0 - UTMIP_HSSQUELCH_LEVEL_NEW: 2.
|
|
USB(USB1_UTMIP_SPARE_CFG0) &= 0xFFFFFE67; //patched0 - FUSE_HS_IREF_CAP_CFG
|
|
USB(USB1_UTMIP_TX_CFG0) |= 0x80000;
|
|
|
|
//USB(USB1_UTMIP_HSRX_CFG0) = (USB(USB1_UTMIP_HSRX_CFG0) & 0xFFF003FF) | 0x88000 | 0x4000; unpatched1
|
|
USB(USB1_UTMIP_HSRX_CFG0) = (USB(USB1_UTMIP_HSRX_CFG0) & 0xF0F003FF) | 0x88000 | 0x4000; //patched1 - reset UTMIP_PCOUNT_UPDN_DIV: From 1 to 0.
|
|
USB(USB1_UTMIP_BIAS_CFG2) &= 0xFFFFFFF8; //patched1 - UTMIP_HSSQUELCH_LEVEL_NEW: 0
|
|
|
|
USB(USB1_UTMIP_HSRX_CFG1) = (USB(USB1_UTMIP_HSRX_CFG1) & 0xFFFFFFC1) | 0x12;
|
|
USB(USB1_UTMIP_MISC_CFG1) |= 0x40000000;
|
|
|
|
// Enable crystal clock.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) |= 0x40000000;
|
|
|
|
// Enable USB2 tracking clock.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_Y_SET) = BIT(CLK_Y_USB2_TRK);
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_SOURCE_USB2_HSIC_TRK) = (CLOCK(CLK_RST_CONTROLLER_CLK_SOURCE_USB2_HSIC_TRK) & 0xFFFFFF00) | 6; // Set trank divisor to 4.
|
|
|
|
USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFFC03F07) | 0x78000 | 0x50; // Set delays.
|
|
USB(USB1_UTMIP_BIAS_CFG0) &= 0xFFFFFBFF; // Disable Power down bias circuit.
|
|
usleep(1);
|
|
|
|
// Force PDTRK input into power up.
|
|
USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFFFFFFFE) | 2;
|
|
usleep(100);
|
|
|
|
// TRK cycle done. Force PDTRK input into power down.
|
|
USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFF7FFFFF) | 1;
|
|
usleep(3);
|
|
|
|
// Force PDTRK input into power up.
|
|
USB(USB1_UTMIP_BIAS_CFG1) = USB(USB1_UTMIP_BIAS_CFG1) & 0xFFFFFFFE;
|
|
usleep(100);
|
|
|
|
// TRK cycle done. Force PDTRK input into power down.
|
|
USB(USB1_UTMIP_BIAS_CFG1) = (USB(USB1_UTMIP_BIAS_CFG1) & 0xFF7FFFFF) | 1;
|
|
|
|
// Disable USB2 tracking clock and configure UTMIP misc.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_Y_CLR) = BIT(CLK_Y_USB2_TRK);
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) = (CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) & 0xFEFFFFEA) | 0x2000000 | 0x28 | 2;
|
|
usleep(1);
|
|
|
|
USB(USB1_UTMIP_BIAS_CFG0) &= 0xFF3FF7FF;
|
|
usleep(1);
|
|
|
|
// Clear power downs on UTMIP ID and VBUS wake up, PD, PD2, PDZI, PDCHRP, PDDR.
|
|
PMC(APBDEV_PMC_USB_AO) &= 0xFFFFFFF3; // UTMIP ID and VBUS wake up.
|
|
usleep(1);
|
|
USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFFFBFFF; // UTMIP_FORCE_PD_POWERDOWN.
|
|
usleep(1);
|
|
USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFFEFFFF; // UTMIP_FORCE_PD2_POWERDOWN.
|
|
usleep(1);
|
|
USB(USB1_UTMIP_XCVR_CFG0) &= 0xFFFBFFFF; // UTMIP_FORCE_PDZI_POWERDOWN.
|
|
usleep(1);
|
|
USB(USB1_UTMIP_XCVR_CFG1) &= 0xFFFFFFFB; // UTMIP_FORCE_PDCHRP_POWERDOWN.
|
|
usleep(1);
|
|
USB(USB1_UTMIP_XCVR_CFG1) &= 0xFFFFFFEF; // UTMIP_FORCE_PDDR_POWERDOWN.
|
|
usleep(1);
|
|
}
|
|
|
|
int usb_device_init()
|
|
{
|
|
if (usb_init_done)
|
|
return USB_RES_OK;
|
|
|
|
// Initialize USB2 controller PHY.
|
|
_usb_init_phy();
|
|
|
|
// AHB USB performance cfg.
|
|
AHB_GIZMO(AHB_GIZMO_AHB_MEM) |= AHB_MEM_DONT_SPLIT_AHB_WR | AHB_MEM_ENB_FAST_REARBITRATE;
|
|
AHB_GIZMO(AHB_GIZMO_USB) |= AHB_GIZMO_IMMEDIATE;
|
|
AHB_GIZMO(AHB_ARBITRATION_PRIORITY_CTRL) = PRIORITY_CTRL_WEIGHT(7) | PRIORITY_SELECT_USB;
|
|
AHB_GIZMO(AHB_AHB_MEM_PREFETCH_CFG1) =
|
|
MEM_PREFETCH_ENABLE | MEM_PREFETCH_USB_MST_ID | MEM_PREFETCH_ADDR_BNDRY(12) | 0x1000; // Addr boundary 64KB, Inactivity 4096 cycles.
|
|
|
|
// Set software and hardware context storage and clear it.
|
|
usbdaemon = (usbd_t *)USBD_ADDR; // Depends on USB_TD_BUFFER_PAGE_SIZE aligned address.
|
|
usbd_otg = &usbd_usb_otg_controller_ctxt;
|
|
memset(usbd_otg, 0, sizeof(usbd_controller_t));
|
|
memset(usbdaemon, 0, sizeof(usbd_t));
|
|
|
|
usbd_otg->regs = (t210_usb2d_t *)USB_OTG_BASE;
|
|
usbd_otg->usb_phy_ready = false;
|
|
|
|
// Initialize USB PHY on the USB_OTG Controller (#1) in Device mode.
|
|
int res = _usbd_reset_usb_otg_phy_device_mode();
|
|
usbd_otg->configuration_set = false;
|
|
|
|
_usb_charger_detect();
|
|
|
|
if (!res)
|
|
usb_init_done = true;
|
|
|
|
return res;
|
|
}
|
|
|
|
static void _usb_device_power_down()
|
|
{
|
|
// Enable PHY low power suspend.
|
|
usbd_otg->regs->hostpc1_devlc |= USB2D_HOSTPC1_DEVLC_PHCD;
|
|
// Do not use any controller regs after the above!
|
|
// A reset or clear of the PHCD suspend bit must happen.
|
|
|
|
// Power down OTG and Bias circuits.
|
|
USB(USB1_UTMIP_BIAS_CFG0) |= BIT(11) | BIT(10); // UTMIP_OTGPD, UTMIP_BIASPD.
|
|
|
|
// Power down ID detectors.
|
|
USB(USB1_UTMIP_BIAS_CFG0) |= BIT(23) | BIT(22); // UTMIP_IDPD_SEL, UTMIP_IDPD_VAL.
|
|
|
|
if (usbd_otg->charger_detect)
|
|
{
|
|
USB(USB1_UTMIP_BAT_CHRG_CFG0) = 1; //UTMIP_PD_CHRG
|
|
usbd_otg->charger_detect = 0;
|
|
}
|
|
|
|
// Power down the UTMIP transceivers.
|
|
// UTMIP_FORCE_PDZI_POWERDOWN, UTMIP_FORCE_PD2_POWERDOWN, UTMIP_FORCE_PD_POWERDOWN.
|
|
USB(USB1_UTMIP_XCVR_CFG0) |= BIT(18) | BIT(16) |BIT(14);
|
|
// UTMIP_FORCE_PDDR_POWERDOWN, UTMIP_FORCE_PDCHRP_POWERDOWN, UTMIP_FORCE_PDDISC_POWERDOWN.
|
|
USB(USB1_UTMIP_XCVR_CFG1) |= BIT(4) | BIT(2) | BIT(0);
|
|
|
|
// Keep UTMIP in reset.
|
|
USB(USB1_IF_USB_SUSP_CTRL) |= SUSP_CTRL_UTMIP_RESET;
|
|
|
|
// Power down PD trunk.
|
|
USB(USB1_UTMIP_BIAS_CFG1) |= BIT(0); //UTMIP_FORCE_PDTRK_POWERDOWN.
|
|
|
|
// Force UTMIP_PLL power down.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) |= BIT(14); // UTMIP_FORCE_PLL_ENABLE_POWERDOWN.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) |= BIT(12); // UTMIP_FORCE_PLL_ACTIVE_POWERDOWN.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG2) |= BIT(4) | BIT(0); // UTMIP_FORCE_PD_SAMP_A/C_POWERDOWN.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIP_PLL_CFG1) |= BIT(16); // UTMIP_FORCE_PLLU_POWERDOWN.
|
|
|
|
// Disable crystal clock.
|
|
USB(USB1_UTMIP_MISC_CFG1) &= 0xBFFFFFFF;
|
|
|
|
// Force enable UTMIPLL IDDQ.
|
|
CLOCK(CLK_RST_CONTROLLER_UTMIPLL_HW_PWRDN_CFG0) |= 3;
|
|
|
|
// Set XUSB_PADCTL reset
|
|
CLOCK(CLK_RST_CONTROLLER_RST_DEV_W_SET) = BIT(CLK_W_XUSB_PADCTL);
|
|
|
|
// Disable USBD clock.
|
|
CLOCK(CLK_RST_CONTROLLER_CLK_ENB_L_CLR) = BIT(CLK_L_USBD);
|
|
|
|
// Disable PLLU.
|
|
clock_disable_pllu();
|
|
|
|
usb_init_done = false;
|
|
}
|
|
|
|
static void _usbd_stall_reset_ep1(usb_dir_t direction, usb_ep_cfg_t stall)
|
|
{
|
|
stall &= 1;
|
|
if (direction == USB_DIR_IN)
|
|
{
|
|
usbd_otg->regs->endptctrl[1] = (usbd_otg->regs->endptctrl[1] & ~USB2D_ENDPTCTRL_TX_EP_STALL) | ((u32)stall << 16);
|
|
if (!stall)
|
|
usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_TX_EP_RESET;
|
|
}
|
|
else
|
|
{
|
|
usbd_otg->regs->endptctrl[1] = (usbd_otg->regs->endptctrl[1] & ~USB2D_ENDPTCTRL_RX_EP_STALL) | stall;
|
|
if (!stall)
|
|
usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_RX_EP_RESET;
|
|
}
|
|
}
|
|
|
|
void usb_device_stall_ep1_bulk_out()
|
|
{
|
|
_usbd_stall_reset_ep1(USB_DIR_OUT, USB_EP_CFG_STALL);
|
|
}
|
|
|
|
void usb_device_stall_ep1_bulk_in()
|
|
{
|
|
_usbd_stall_reset_ep1(USB_DIR_IN, USB_EP_CFG_STALL);
|
|
}
|
|
|
|
static int _usbd_get_max_pkt_length(int endpoint)
|
|
{
|
|
switch (endpoint)
|
|
{
|
|
case USB_EP_CTRL_OUT:
|
|
case USB_EP_CTRL_IN:
|
|
return 64;
|
|
case USB_EP_BULK_OUT:
|
|
case USB_EP_BULK_IN:
|
|
if (usbd_otg->port_speed == USB_HIGH_SPEED)
|
|
return 512;
|
|
else
|
|
return 64;
|
|
default:
|
|
return 64;
|
|
}
|
|
}
|
|
|
|
static void _usbd_initialize_ep_ctrl(u32 endpoint)
|
|
{
|
|
usb_hw_ep_t actual_ep = (endpoint & 2) >> 1;
|
|
usb_dir_t direction = endpoint & 1;
|
|
|
|
memset((void *)&usbdaemon->qhs[endpoint], 0, sizeof(dQH_t));
|
|
|
|
if (!endpoint)
|
|
usbdaemon->qhs[endpoint].ep_capabilities = USB_QHD_EP_CAP_IOS_ENABLE;
|
|
|
|
usbdaemon->qhs[endpoint].next_dTD_ptr = 1; // TERMINATE_SET
|
|
|
|
u32 max_packet_len = _usbd_get_max_pkt_length(endpoint) & USB_QHD_EP_CAP_MAX_PKT_LEN_MASK;
|
|
usbdaemon->qhs[endpoint].ep_capabilities |= max_packet_len << 16;
|
|
|
|
if (direction == USB_DIR_IN)
|
|
{
|
|
u32 endpoint_type = usbd_otg->regs->endptctrl[actual_ep] & ~USB2D_ENDPTCTRL_TX_EP_TYPE_MASK;
|
|
if (actual_ep)
|
|
endpoint_type |= usbd_otg->gadget ? USB2D_ENDPTCTRL_TX_EP_TYPE_INTR : USB2D_ENDPTCTRL_TX_EP_TYPE_BULK;
|
|
else
|
|
endpoint_type |= USB2D_ENDPTCTRL_TX_EP_TYPE_CTRL;
|
|
|
|
usbd_otg->regs->endptctrl[actual_ep] = endpoint_type;
|
|
|
|
usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_TX_EP_STALL;
|
|
|
|
if (actual_ep == USB_HW_EP1)
|
|
usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_TX_EP_RESET;
|
|
|
|
usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_TX_EP_ENABLE;
|
|
}
|
|
else // EP Bulk OUT.
|
|
{
|
|
u32 endpoint_type = usbd_otg->regs->endptctrl[actual_ep] & ~USB2D_ENDPTCTRL_RX_EP_TYPE_MASK;
|
|
if (actual_ep)
|
|
{
|
|
endpoint_type |= usbd_otg->gadget ? USB2D_ENDPTCTRL_RX_EP_TYPE_INTR : USB2D_ENDPTCTRL_RX_EP_TYPE_BULK;
|
|
}
|
|
else
|
|
endpoint_type |= USB2D_ENDPTCTRL_RX_EP_TYPE_CTRL;
|
|
|
|
usbd_otg->regs->endptctrl[actual_ep] = endpoint_type;
|
|
usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_RX_EP_STALL;
|
|
|
|
if (actual_ep == USB_HW_EP1)
|
|
usbd_otg->regs->endptctrl[1] |= USB2D_ENDPTCTRL_RX_EP_RESET;
|
|
|
|
usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_RX_EP_ENABLE;
|
|
}
|
|
}
|
|
|
|
static int _usbd_initialize_ep0()
|
|
{
|
|
memset((void *)usbdaemon->qhs, 0, sizeof(dQH_t) * 4); // Clear all used EP queue heads.
|
|
memset((void *)usbdaemon->dtds, 0, sizeof(dTD_t) * 4); // Clear all used EP0 token heads.
|
|
|
|
usbd_otg->regs->asynclistaddr = (u32)usbdaemon->qhs;
|
|
|
|
_usbd_initialize_ep_ctrl(USB_EP_CTRL_OUT);
|
|
_usbd_initialize_ep_ctrl(USB_EP_CTRL_IN);
|
|
|
|
// Disable Auto Low Power.
|
|
usbd_otg->regs->hostpc1_devlc &= ~USB2D_HOSTPC1_DEVLC_ASUS;
|
|
|
|
// Initiate an attach event.
|
|
usbd_otg->regs->usbcmd |= USB2D_USBCMD_RUN;
|
|
|
|
u32 retries = 100000; // 200ms timeout.
|
|
while (!(usbd_otg->regs->usbcmd & USB2D_USBCMD_RUN))
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_TIMEOUT;
|
|
usleep(1);
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
// static void _disable_usb_wdt4()
|
|
// {
|
|
// if (TIMER_WDT4_STATUS & 1)// active
|
|
// {
|
|
// TIMER_TMR0_TMR_PTV &= 0x7FFFFFFF; // Disable timer
|
|
// TIMER_WDT4_UNLOCK_PATTERN = 0xC45A; // Alow writes to disable counter bit.
|
|
// TIMER_WDT4_COMMAND |= 2; // Disable counter
|
|
// TIMER_TMR0_TMR_PCR |= 0x40000000;// INTR_CLR
|
|
// }
|
|
// }
|
|
|
|
int usbd_flush_endpoint(u32 endpoint)
|
|
{
|
|
|
|
usb_hw_ep_t actual_ep = (endpoint & 2) >> 1;
|
|
usb_dir_t direction = endpoint & 1;
|
|
u32 reg_mask = endpoint;
|
|
|
|
// Flash all endpoints or 1.
|
|
if (endpoint != USB_EP_ALL)
|
|
{
|
|
if (direction == USB_DIR_IN)
|
|
reg_mask = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep;
|
|
else
|
|
reg_mask = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep;
|
|
}
|
|
usbd_otg->regs->endptflush = reg_mask;
|
|
|
|
u32 retries = 100000; // 200ms timeout.
|
|
while (usbd_otg->regs->endptflush & reg_mask)
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_TIMEOUT;
|
|
usleep(1);
|
|
}
|
|
|
|
// Wait for the endpoint to finish all transactions (buffer not ready).
|
|
retries = 100000; // 200ms timeout.
|
|
while (usbd_otg->regs->endptstatus & reg_mask)
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_TIMEOUT;
|
|
usleep(1);
|
|
}
|
|
|
|
// Wait for the endpoint to clear the primed status.
|
|
retries = 100000; // 200ms timeout.
|
|
while (usbd_otg->regs->endptprime & reg_mask)
|
|
{
|
|
retries--;
|
|
if (!retries)
|
|
return USB_ERROR_TIMEOUT;
|
|
usleep(1);
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
void usbd_end(bool reset_ep, bool only_controller)
|
|
{
|
|
if (reset_ep)
|
|
{
|
|
usbd_flush_endpoint(USB_EP_ALL);
|
|
_usbd_stall_reset_ep1(USB_DIR_OUT, USB_EP_CFG_RESET); // EP1 Bulk OUT.
|
|
_usbd_stall_reset_ep1(USB_DIR_IN, USB_EP_CFG_RESET); // EP1 Bulk IN.
|
|
|
|
usbd_otg->config_num = 0;
|
|
usbd_otg->interface_num = 0;
|
|
usbd_otg->configuration_set = false;
|
|
usbd_otg->max_lun_set = false;
|
|
}
|
|
|
|
// Stop device controller.
|
|
usbd_otg->regs->usbcmd &= ~USB2D_USBCMD_RUN;
|
|
|
|
// Enable PHY auto low power suspend.
|
|
usbd_otg->regs->hostpc1_devlc |= USB2D_HOSTPC1_DEVLC_ASUS;
|
|
|
|
if (!only_controller)
|
|
_usb_device_power_down();
|
|
}
|
|
|
|
static void _usbd_mark_ep_complete(u32 endpoint)
|
|
{
|
|
u32 complete_bit;
|
|
usb_hw_ep_t actual_ep = (endpoint & 2) >> 1;
|
|
usb_dir_t direction = endpoint & 1;
|
|
|
|
usbd_flush_endpoint(endpoint);
|
|
memset((void *)&usbdaemon->dtds[endpoint * 4], 0, sizeof(dTD_t) * 4);
|
|
memset((void *)&usbdaemon->qhs[endpoint], 0, sizeof(dQH_t));
|
|
usbdaemon->ep_configured[endpoint] = 0;
|
|
usbdaemon->ep_bytes_requested[endpoint] = 0;
|
|
|
|
if (direction == USB_DIR_IN)
|
|
complete_bit = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep;
|
|
else
|
|
complete_bit = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep;
|
|
|
|
usbd_otg->regs->endptcomplete |= complete_bit;
|
|
}
|
|
|
|
static usb_ep_status_t _usbd_get_ep_status(usb_ep_t endpoint)
|
|
{
|
|
bool status;
|
|
u32 reg_val;
|
|
u32 reg_mask;
|
|
u32 actual_ep = (endpoint & 2) >> 1;
|
|
usb_dir_t direction = endpoint & 1;
|
|
|
|
if (direction == USB_DIR_IN)
|
|
reg_mask = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep;
|
|
else
|
|
reg_mask = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep;
|
|
|
|
if (actual_ep == USB_HW_EP1)
|
|
reg_val = usbd_otg->regs->endptctrl[1];
|
|
else
|
|
reg_val = usbd_otg->regs->endptctrl[0];
|
|
|
|
// Check stalled status.
|
|
if (direction == USB_DIR_IN)
|
|
status = reg_val & USB2D_ENDPTCTRL_TX_EP_STALL;
|
|
else
|
|
status = reg_val & USB2D_ENDPTCTRL_RX_EP_STALL;
|
|
|
|
if (status)
|
|
return USB_EP_STATUS_STALLED;
|
|
|
|
// Check enabled status.
|
|
if (direction == USB_DIR_IN)
|
|
status = reg_val & USB2D_ENDPTCTRL_TX_EP_ENABLE;
|
|
else
|
|
status = reg_val & USB2D_ENDPTCTRL_RX_EP_ENABLE;
|
|
|
|
if (!status)
|
|
return USB_EP_STATUS_DISABLED;
|
|
|
|
// CHeck qHD error status.
|
|
u32 token_error_mask = USB_QHD_TOKEN_HALTED | USB_QHD_TOKEN_BUFFER_ERROR | USB_QHD_TOKEN_XFER_ERROR;
|
|
if (usbdaemon->qhs[endpoint].token & token_error_mask)
|
|
return USB_EP_STATUS_ERROR;
|
|
|
|
// Check if endpoint has a request or a ready buffer.
|
|
if ((usbd_otg->regs->endptprime & reg_mask) || (usbd_otg->regs->endptstatus & reg_mask))
|
|
return USB_EP_STATUS_ACTIVE; // RX/TX active.
|
|
|
|
// Return idle or not configured status.
|
|
if (!usbdaemon->ep_configured[endpoint])
|
|
return USB_EP_STATUS_NO_CONFIG;
|
|
|
|
return USB_EP_STATUS_IDLE;
|
|
}
|
|
|
|
static int _usbd_ep_operation(usb_ep_t endpoint, u8 *buf, u32 len, bool sync)
|
|
{
|
|
if (!buf)
|
|
len = 0;
|
|
|
|
u32 prime_bit;
|
|
usb_hw_ep_t actual_ep = (endpoint & 2) >> 1;
|
|
usb_dir_t direction = endpoint & 1;
|
|
u32 length_left = len;
|
|
u32 dtd_ep_idx = endpoint * 4;
|
|
|
|
_usbd_mark_ep_complete(endpoint);
|
|
|
|
if (endpoint == USB_EP_CTRL_OUT)
|
|
usbdaemon->qhs[endpoint].ep_capabilities = USB_QHD_EP_CAP_IOS_ENABLE;
|
|
|
|
u32 max_packet_len = _usbd_get_max_pkt_length(endpoint) & USB_QHD_EP_CAP_MAX_PKT_LEN_MASK;
|
|
usbdaemon->qhs[endpoint].ep_capabilities |= (max_packet_len << 16) | USB_QHD_EP_CAP_ZERO_LEN_TERM_DIS;
|
|
usbdaemon->qhs[endpoint].next_dTD_ptr = 0; // Clear terminate bit.
|
|
//usbdaemon->qhs[endpoint].ep_capabilities |= USB_QHD_TOKEN_IRQ_ON_COMPLETE;
|
|
|
|
usbdaemon->ep_configured[endpoint] = 1;
|
|
usbdaemon->ep_bytes_requested[endpoint] = len;
|
|
|
|
// Configure dTD.
|
|
u32 dtd_idx = 0;
|
|
do
|
|
{
|
|
if (dtd_idx)
|
|
usbdaemon->dtds[dtd_ep_idx + dtd_idx - 1].next_dTD = (u32)&usbdaemon->dtds[dtd_ep_idx + dtd_idx];
|
|
|
|
u32 dtd_size = MIN(length_left, USB_TD_BUFFER_MAX_SIZE); // 16KB max per dTD.
|
|
usbdaemon->dtds[dtd_ep_idx + dtd_idx].info = (dtd_size << 16) | USB_QHD_TOKEN_ACTIVE;
|
|
// usbdaemon->dtds[dtd_ep_idx + dtd_idx].info |= USB_QHD_TOKEN_IRQ_ON_COMPLETE;
|
|
|
|
// Set buffers addresses to all page pointers.
|
|
u32 dt_buffer_offset = dtd_idx * USB_TD_BUFFER_MAX_SIZE;
|
|
for (u32 i = 0; i < 4; i++)
|
|
usbdaemon->dtds[dtd_ep_idx + dtd_idx].pages[i] =
|
|
(u32)&buf[dt_buffer_offset + (USB_TD_BUFFER_PAGE_SIZE * i)];
|
|
|
|
//usbdaemon->dtds[dtd_ep_idx + dtd_idx].pages[5] =
|
|
// (u32)&buf[dt_buffer_offset + (USB_TD_BUFFER_PAGE_SIZE * 4)]; // Last buffer. Unused.
|
|
|
|
length_left -= dtd_size;
|
|
if (length_left)
|
|
dtd_idx++;
|
|
}
|
|
while (length_left);
|
|
|
|
// Last dTD, terminate it.
|
|
usbdaemon->dtds[dtd_ep_idx + dtd_idx].next_dTD = 1;
|
|
|
|
// Set first dTD address to queue head next dTD.
|
|
usbdaemon->qhs[endpoint].next_dTD_ptr |= (u32)&usbdaemon->dtds[dtd_ep_idx] & 0xFFFFFFE0;
|
|
|
|
// Flush AHB prefetcher.
|
|
AHB_GIZMO(AHB_AHB_MEM_PREFETCH_CFG1) &= ~MEM_PREFETCH_ENABLE;
|
|
AHB_GIZMO(AHB_AHB_MEM_PREFETCH_CFG1) |= MEM_PREFETCH_ENABLE;
|
|
|
|
if (direction == USB_DIR_IN)
|
|
{
|
|
prime_bit = USB2D_ENDPT_STATUS_TX_OFFSET << actual_ep;
|
|
bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLN_INV_WAY, false);
|
|
}
|
|
else
|
|
prime_bit = USB2D_ENDPT_STATUS_RX_OFFSET << actual_ep;
|
|
|
|
// Prime endpoint.
|
|
usbd_otg->regs->endptprime |= prime_bit; // USB2_CONTROLLER_USB2D_ENDPTPRIME.
|
|
|
|
int res = USB_RES_OK;
|
|
usb_ep_status_t ep_status;
|
|
if (sync)
|
|
{
|
|
ep_status = _usbd_get_ep_status(endpoint);
|
|
if (ep_status == USB_EP_STATUS_ACTIVE)
|
|
{
|
|
u32 retries = 1000000; // Timeout 2s.
|
|
while (retries)
|
|
{
|
|
ep_status = _usbd_get_ep_status(endpoint);
|
|
if (ep_status != USB_EP_STATUS_ACTIVE)
|
|
{
|
|
if (ep_status == USB_EP_STATUS_DISABLED)
|
|
res = USB2_ERROR_XFER_EP_DISABLED;
|
|
goto out;
|
|
}
|
|
retries--;
|
|
usleep(1);
|
|
}
|
|
res = USB_ERROR_TIMEOUT;
|
|
}
|
|
else if (ep_status == USB_EP_STATUS_DISABLED)
|
|
res = USB2_ERROR_XFER_EP_DISABLED;
|
|
out:
|
|
if (res)
|
|
_usbd_mark_ep_complete(endpoint);
|
|
else if (_usbd_get_ep_status(endpoint) != USB_EP_STATUS_IDLE)
|
|
res = USB_ERROR_XFER_ERROR;
|
|
|
|
if (direction == USB_DIR_OUT)
|
|
bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLN_INV_WAY, false);
|
|
}
|
|
|
|
return res;
|
|
}
|
|
|
|
static int _usbd_ep_ack(usb_ep_t ep)
|
|
{
|
|
return _usbd_ep_operation(ep, NULL, 0, true);
|
|
}
|
|
|
|
static void _usbd_set_ep0_stall()
|
|
{
|
|
// EP Control endpoints must be always stalled together.
|
|
usbd_otg->regs->endptctrl[0] =
|
|
USB2D_ENDPTCTRL_TX_EP_ENABLE | USB2D_ENDPTCTRL_TX_EP_STALL |
|
|
USB2D_ENDPTCTRL_RX_EP_ENABLE | USB2D_ENDPTCTRL_RX_EP_STALL;
|
|
}
|
|
|
|
int usbd_set_ep_stall(u32 endpoint, int ep_stall)
|
|
{
|
|
usb_hw_ep_t actual_ep = (endpoint & 2) >> 1;
|
|
usb_dir_t direction = endpoint & 1;
|
|
|
|
if (ep_stall)
|
|
{
|
|
if (direction == USB_DIR_IN)
|
|
usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_TX_EP_STALL; // Stall EP Bulk IN.
|
|
else
|
|
usbd_otg->regs->endptctrl[actual_ep] |= USB2D_ENDPTCTRL_RX_EP_STALL; // Stall EP Bulk OUT.
|
|
}
|
|
else
|
|
{
|
|
if (direction == USB_DIR_IN)
|
|
usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_TX_EP_STALL; // Clear stall EP Bulk IN.
|
|
else
|
|
usbd_otg->regs->endptctrl[actual_ep] &= ~USB2D_ENDPTCTRL_RX_EP_STALL; // Clear stall EP Bulk OUT.
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
static void _usbd_handle_get_class_request(bool *transmit_data, u8 *descriptor, int *size, bool *ep_stall)
|
|
{
|
|
u8 _bRequest = usbd_otg->control_setup.bRequest;
|
|
u16 _wIndex = usbd_otg->control_setup.wIndex;
|
|
u16 _wValue = usbd_otg->control_setup.wValue;
|
|
u16 _wLength = usbd_otg->control_setup.wLength;
|
|
|
|
bool valid_interface = _wIndex == usbd_otg->interface_num;
|
|
bool valid_len = (_bRequest == USB_REQUEST_BULK_GET_MAX_LUN) ? 1 : 0;
|
|
|
|
if (!valid_interface || _wValue != 0 || _wLength != valid_len)
|
|
{
|
|
*ep_stall = true;
|
|
return;
|
|
}
|
|
|
|
switch (_bRequest)
|
|
{
|
|
case USB_REQUEST_BULK_RESET:
|
|
_usbd_ep_ack(USB_EP_CTRL_IN);
|
|
usbd_otg->bulk_reset_req = true;
|
|
break; // DELAYED_STATUS;
|
|
case USB_REQUEST_BULK_GET_MAX_LUN:
|
|
*transmit_data = true;
|
|
*size = 1;
|
|
descriptor[0] = usbd_otg->max_lun; // Set 0 LUN for 1 drive supported.
|
|
usbd_otg->max_lun_set = true;
|
|
break;
|
|
default:
|
|
*ep_stall = true;
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void _usbd_handle_get_descriptor(bool *transmit_data, void **descriptor, int *size, bool *ep_stall)
|
|
{
|
|
u8 descriptor_type = usbd_otg->control_setup.wValue >> 8;
|
|
u8 descriptor_subtype = usbd_otg->control_setup.wValue & 0xFF;
|
|
|
|
switch (descriptor_type)
|
|
{
|
|
case USB_DESCRIPTOR_DEVICE:
|
|
{
|
|
/*
|
|
u32 soc_rev = APB_MISC(APB_MISC_GP_HIDREV);
|
|
usb_device_descriptor.idProduct = (soc_rev >> 8) & 0xFF; // chip_id.
|
|
usb_device_descriptor.idProduct |= ((soc_rev << 4) | (FUSE(FUSE_SKU_INFO) & 0xF)) << 8; // HIDFAM.
|
|
usb_device_descriptor.bcdDevice = (soc_rev >> 16) & 0xF; // MINORREV.
|
|
usb_device_descriptor.bcdDevice |= ((soc_rev >> 4) & 0xF) << 8; // MAJORREV.
|
|
*/
|
|
*descriptor = usbd_otg->desc->dev;
|
|
*size = usbd_otg->desc->dev->bLength;
|
|
*transmit_data = true;
|
|
return;
|
|
}
|
|
case USB_DESCRIPTOR_CONFIGURATION:
|
|
if (usbd_otg->gadget == USB_GADGET_UMS)
|
|
{
|
|
if (usbd_otg->port_speed == USB_HIGH_SPEED) // High speed. 512 bytes.
|
|
{
|
|
usbd_otg->desc->cfg->endpoint[0].wMaxPacketSize = 0x200;
|
|
usbd_otg->desc->cfg->endpoint[1].wMaxPacketSize = 0x200;
|
|
}
|
|
else // Full speed. 64 bytes.
|
|
{
|
|
usbd_otg->desc->cfg->endpoint[0].wMaxPacketSize = 0x40;
|
|
usbd_otg->desc->cfg->endpoint[1].wMaxPacketSize = 0x40;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
usb_cfg_hid_descr_t *tmp = (usb_cfg_hid_descr_t *)usbd_otg->desc->cfg;
|
|
if (usbd_otg->port_speed == USB_HIGH_SPEED) // High speed. 512 bytes.
|
|
{
|
|
tmp->endpoint[0].wMaxPacketSize = 0x200;
|
|
tmp->endpoint[1].wMaxPacketSize = 0x200;
|
|
tmp->endpoint[0].bInterval = usbd_otg->gadget == USB_GADGET_HID_GAMEPAD ? 4 : 3; // 8ms : 4ms.
|
|
tmp->endpoint[1].bInterval = usbd_otg->gadget == USB_GADGET_HID_GAMEPAD ? 4 : 3; // 8ms : 4ms.
|
|
}
|
|
else // Full speed. 64 bytes.
|
|
{
|
|
tmp->endpoint[0].wMaxPacketSize = 0x40;
|
|
tmp->endpoint[1].wMaxPacketSize = 0x40;
|
|
tmp->endpoint[0].bInterval = usbd_otg->gadget == USB_GADGET_HID_GAMEPAD ? 8 : 4; // 8ms : 4ms.
|
|
tmp->endpoint[1].bInterval = usbd_otg->gadget == USB_GADGET_HID_GAMEPAD ? 8 : 4; // 8ms : 4ms.
|
|
}
|
|
}
|
|
*descriptor = usbd_otg->desc->cfg;
|
|
*size = usbd_otg->desc->cfg->config.wTotalLength;
|
|
*transmit_data = true;
|
|
return;
|
|
case USB_DESCRIPTOR_STRING:
|
|
switch (descriptor_subtype)
|
|
{
|
|
case 1:
|
|
*descriptor = usbd_otg->desc->vendor;
|
|
*size = usbd_otg->desc->vendor[0];
|
|
break;
|
|
case 2:
|
|
*descriptor = usbd_otg->desc->product;
|
|
*size = usbd_otg->desc->product[0];
|
|
break;
|
|
case 3:
|
|
*descriptor = usbd_otg->desc->serial;
|
|
*size = usbd_otg->desc->serial[0];
|
|
break;
|
|
case 0xEE:
|
|
*descriptor = usbd_otg->desc->ms_os;
|
|
*size = usbd_otg->desc->ms_os->bLength;
|
|
break;
|
|
default:
|
|
*descriptor = usbd_otg->desc->lang_id;
|
|
*size = 4;
|
|
break;
|
|
}
|
|
*transmit_data = true;
|
|
return;
|
|
case USB_DESCRIPTOR_DEVICE_QUALIFIER:
|
|
if (!usbd_otg->desc->dev_qual)
|
|
goto exit;
|
|
usbd_otg->desc->dev_qual->bNumOtherConfigs = 1;
|
|
*descriptor = usbd_otg->desc->dev_qual;
|
|
*size = usbd_otg->desc->dev_qual->bLength;
|
|
*transmit_data = true;
|
|
return;
|
|
case USB_DESCRIPTOR_OTHER_SPEED_CONFIGURATION:
|
|
if (!usbd_otg->desc->cfg_other)
|
|
goto exit;
|
|
if (usbd_otg->port_speed == USB_HIGH_SPEED)
|
|
{
|
|
usbd_otg->desc->cfg_other->endpoint[0].wMaxPacketSize = 0x40;
|
|
usbd_otg->desc->cfg_other->endpoint[1].wMaxPacketSize = 0x40;
|
|
}
|
|
else
|
|
{
|
|
usbd_otg->desc->cfg_other->endpoint[0].wMaxPacketSize = 0x200;
|
|
usbd_otg->desc->cfg_other->endpoint[1].wMaxPacketSize = 0x200;
|
|
}
|
|
if ((usbd_otg->charger_detect & 1) && (usbd_otg->charger_detect & 2))
|
|
usbd_otg->desc->cfg_other->config.bMaxPower = 500 / 2;
|
|
*descriptor = usbd_otg->desc->cfg_other;
|
|
*size = usbd_otg->desc->cfg_other->config.wTotalLength;
|
|
*transmit_data = true;
|
|
return;
|
|
case USB_DESCRIPTOR_DEVICE_BINARY_OBJECT:
|
|
*descriptor = usbd_otg->desc->dev_bot;
|
|
*size = usbd_otg->desc->dev_bot->wTotalLength;
|
|
*transmit_data = true;
|
|
return;
|
|
default:
|
|
*transmit_data = false;
|
|
*ep_stall = true;
|
|
return;
|
|
}
|
|
exit:
|
|
*transmit_data = false;
|
|
*ep_stall = true;
|
|
return;
|
|
}
|
|
|
|
static int _usbd_handle_set_request(bool *ep_stall)
|
|
{
|
|
int res = USB_RES_OK;
|
|
u8 bRequest = usbd_otg->control_setup.bRequest;
|
|
if (bRequest == USB_REQUEST_SET_ADDRESS)
|
|
{
|
|
res = _usbd_ep_ack(USB_EP_CTRL_IN);
|
|
|
|
// Set USB address for device mode.
|
|
if (!res)
|
|
usbd_otg->regs->periodiclistbase = (usbd_otg->regs->periodiclistbase & 0x1FFFFFF) | ((usbd_otg->control_setup.wValue & 0xFF) << 25);
|
|
}
|
|
else if (bRequest == USB_REQUEST_SET_CONFIGURATION)
|
|
{
|
|
res = _usbd_ep_ack(USB_EP_CTRL_IN);
|
|
if (!res)
|
|
{
|
|
usbd_otg->config_num = usbd_otg->control_setup.wValue;
|
|
_usbd_initialize_ep_ctrl(USB_EP_BULK_OUT);
|
|
_usbd_initialize_ep_ctrl(USB_EP_BULK_IN);
|
|
usbd_otg->configuration_set = true;
|
|
}
|
|
}
|
|
else
|
|
*ep_stall = true;
|
|
|
|
return res;
|
|
}
|
|
|
|
static int _usbd_handle_ep0_control_transfer()
|
|
{
|
|
int res = USB_RES_OK;
|
|
bool ep_stall = false;
|
|
bool transmit_data = false;
|
|
|
|
u8 *descriptor = (u8 *)USB_DESCRIPTOR_ADDR;
|
|
int size = 0;
|
|
|
|
u8 _bmRequestType = usbd_otg->control_setup.bmRequestType;
|
|
u8 _bRequest = usbd_otg->control_setup.bRequest;
|
|
u16 _wValue = usbd_otg->control_setup.wValue;
|
|
u16 _wIndex = usbd_otg->control_setup.wIndex;
|
|
u16 _wLength = usbd_otg->control_setup.wLength;
|
|
|
|
//gfx_printf("%02X %02X %04X %04X %04X\n", _bmRequestType, _bRequest, _wValue, _wIndex, _wLength);
|
|
|
|
switch (_bmRequestType)
|
|
{
|
|
case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_DEVICE):
|
|
res = _usbd_handle_set_request(&ep_stall);
|
|
break;
|
|
|
|
case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_INTERFACE):
|
|
res = _usbd_ep_ack(USB_EP_CTRL_IN);
|
|
if (!res)
|
|
usbd_otg->interface_num = _wValue;
|
|
break;
|
|
|
|
case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT):
|
|
switch (_bRequest)
|
|
{
|
|
case USB_REQUEST_CLEAR_FEATURE:
|
|
case USB_REQUEST_SET_FEATURE:
|
|
if ((_wValue & 0xFF) == USB_FEATURE_ENDPOINT_HALT)
|
|
{
|
|
int direction;
|
|
switch (_wIndex) // endpoint
|
|
{
|
|
case USB_EP_ADDR_CTRL_OUT:
|
|
direction = 2;
|
|
break;
|
|
case USB_EP_ADDR_CTRL_IN:
|
|
direction = 3;
|
|
break;
|
|
case USB_EP_ADDR_BULK_OUT:
|
|
direction = 0;
|
|
break;
|
|
case USB_EP_ADDR_BULK_IN:
|
|
direction = 1;
|
|
break;
|
|
default:
|
|
_usbd_stall_reset_ep1(3, USB_EP_CFG_STALL);
|
|
goto out;
|
|
}
|
|
|
|
if (_bRequest == USB_REQUEST_CLEAR_FEATURE)
|
|
_usbd_stall_reset_ep1(direction, USB_EP_CFG_RESET);
|
|
else
|
|
_usbd_stall_reset_ep1(direction, USB_EP_CFG_STALL);
|
|
|
|
res = _usbd_ep_ack(USB_EP_CTRL_IN);
|
|
}
|
|
else
|
|
_usbd_stall_reset_ep1(3, USB_EP_CFG_STALL);
|
|
|
|
break;
|
|
default:
|
|
ep_stall = true;
|
|
break;
|
|
}
|
|
break;
|
|
|
|
case (USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE):
|
|
memset(descriptor, 0, _wLength);
|
|
_usbd_handle_get_class_request(&transmit_data, descriptor, &size, &ep_stall);
|
|
break;
|
|
|
|
case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_DEVICE):
|
|
switch (_bRequest)
|
|
{
|
|
case USB_REQUEST_GET_STATUS:
|
|
descriptor[0] = USB_STATUS_DEV_SELF_POWERED;
|
|
descriptor[1] = 0; // No support for remove wake up.
|
|
transmit_data = true;
|
|
size = 2;
|
|
break;
|
|
case USB_REQUEST_GET_DESCRIPTOR:
|
|
_usbd_handle_get_descriptor(&transmit_data, (void **)&descriptor, &size, &ep_stall);
|
|
break;
|
|
case USB_REQUEST_GET_CONFIGURATION:
|
|
descriptor = (u8 *)&usbd_otg->config_num;
|
|
size = _wLength;
|
|
transmit_data = true;
|
|
break;
|
|
default:
|
|
ep_stall = true;
|
|
break;
|
|
}
|
|
break;
|
|
|
|
case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_INTERFACE):
|
|
if (_bRequest == USB_REQUEST_GET_INTERFACE)
|
|
{
|
|
memset(descriptor, 0, _wLength);
|
|
descriptor[0] = usbd_otg->interface_num;
|
|
size = _wLength;
|
|
}
|
|
else if (_bRequest == USB_REQUEST_GET_STATUS)
|
|
{
|
|
memset(descriptor, 0, _wLength);
|
|
size = _wLength;
|
|
}
|
|
else if (_bRequest == USB_REQUEST_GET_DESCRIPTOR && (_wValue >> 8) == USB_DESCRIPTOR_HID_REPORT && usbd_otg->gadget > USB_GADGET_UMS)
|
|
{
|
|
if (usbd_otg->gadget == USB_GADGET_HID_GAMEPAD)
|
|
{
|
|
descriptor = (u8 *)&hid_report_descriptor_jc;
|
|
size = hid_report_descriptor_jc_size;
|
|
}
|
|
else // USB_GADGET_HID_TOUCHPAD
|
|
{
|
|
descriptor = (u8 *)&hid_report_descriptor_touch;
|
|
size = hid_report_descriptor_touch_size;
|
|
}
|
|
|
|
usbd_otg->hid_report_sent = true;
|
|
}
|
|
else
|
|
{
|
|
ep_stall = true;
|
|
break;
|
|
}
|
|
|
|
if (_wLength < size)
|
|
size = _wLength;
|
|
transmit_data = true;
|
|
break;
|
|
|
|
case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT):
|
|
if (_bRequest == USB_REQUEST_GET_STATUS)
|
|
{
|
|
int ep_req;
|
|
switch (_wIndex)
|
|
{
|
|
case USB_EP_ADDR_CTRL_OUT:
|
|
ep_req = USB_EP_CTRL_OUT;
|
|
break;
|
|
case USB_EP_ADDR_BULK_OUT:
|
|
ep_req = USB_EP_BULK_OUT;
|
|
break;
|
|
case USB_EP_ADDR_CTRL_IN:
|
|
ep_req = USB_EP_CTRL_IN;
|
|
break;
|
|
case USB_EP_ADDR_BULK_IN:
|
|
ep_req = USB_EP_BULK_IN;
|
|
break;
|
|
default:
|
|
_usbd_stall_reset_ep1(3, USB_EP_CFG_STALL);
|
|
goto out;
|
|
}
|
|
|
|
size = _wLength;
|
|
memset(descriptor, 0, size);
|
|
|
|
if (_usbd_get_ep_status(ep_req) == USB_EP_STATUS_STALLED)
|
|
descriptor[0] = USB_STATUS_EP_HALTED;
|
|
else
|
|
descriptor[0] = USB_STATUS_EP_OK;
|
|
|
|
transmit_data = true;
|
|
}
|
|
else
|
|
_usbd_stall_reset_ep1(3, USB_EP_CFG_STALL);
|
|
break;
|
|
|
|
case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE):
|
|
memset(descriptor, 0, _wLength);
|
|
_usbd_handle_get_class_request(&transmit_data, descriptor, &size, &ep_stall);
|
|
break;
|
|
|
|
case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_VENDOR | USB_SETUP_RECIPIENT_INTERFACE):
|
|
case (USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_VENDOR | USB_SETUP_RECIPIENT_DEVICE):
|
|
if (_bRequest == USB_REQUEST_GET_MS_DESCRIPTOR)
|
|
{
|
|
switch (_wIndex)
|
|
{
|
|
case USB_DESCRIPTOR_MS_COMPAT_ID:
|
|
descriptor = (u8 *)usbd_otg->desc->ms_cid;
|
|
size = usbd_otg->desc->ms_cid->dLength;
|
|
transmit_data = true;
|
|
break;
|
|
case USB_DESCRIPTOR_MS_EXTENDED_PROPERTIES:
|
|
descriptor = (u8 *)usbd_otg->desc->mx_ext;
|
|
size = usbd_otg->desc->mx_ext->dLength;
|
|
transmit_data = true;
|
|
break;
|
|
default:
|
|
ep_stall = true;
|
|
break;
|
|
}
|
|
}
|
|
else
|
|
ep_stall = true;
|
|
break;
|
|
|
|
default:
|
|
ep_stall = true;
|
|
break;
|
|
}
|
|
|
|
// Transmit data to HOST if any.
|
|
if (transmit_data)
|
|
{
|
|
memcpy(usb_ep0_ctrl_buf, descriptor, size);
|
|
|
|
if (_wLength < size)
|
|
size = _wLength;
|
|
res = _usbd_ep_operation(USB_EP_CTRL_IN, usb_ep0_ctrl_buf, size, true);
|
|
if (!res)
|
|
res = _usbd_ep_ack(USB_EP_CTRL_OUT);
|
|
}
|
|
|
|
out:
|
|
if (ep_stall)
|
|
_usbd_set_ep0_stall();
|
|
|
|
return res;
|
|
}
|
|
|
|
static int _usbd_ep0_initialize()
|
|
{
|
|
bool enter = false;
|
|
if (usbd_otg->configuration_set)
|
|
enter = true;
|
|
else
|
|
{
|
|
usbdaemon->qhs = (volatile dQH_t *)USB2_QH_USB2D_QH_EP_BASE;
|
|
|
|
if (!_usbd_initialize_ep0())
|
|
enter = true;
|
|
}
|
|
|
|
if (enter)
|
|
{
|
|
usbd_otg->configuration_set = false;
|
|
usbd_otg->max_lun_set = false;
|
|
|
|
// Timeout if cable or communication isn't started in 1.5 minutes.
|
|
u32 timer = get_tmr_ms() + 90000;
|
|
while (true)
|
|
{
|
|
u32 usb_status_irqs = usbd_otg->regs->usbsts;
|
|
|
|
// Clear all interrupt statuses.
|
|
usbd_otg->regs->usbsts = usb_status_irqs;
|
|
|
|
// Check if a reset was received.
|
|
if (usb_status_irqs & USB2D_USBSTS_URI)
|
|
{
|
|
//_disable_usb_wdt4();
|
|
|
|
// Clear all device addresses, enabled setup requests, transmit events and flush all endpoints.
|
|
usbd_otg->regs->periodiclistbase = 0;
|
|
usbd_otg->regs->endptsetupstat = usbd_otg->regs->endptsetupstat;
|
|
usbd_otg->regs->endptcomplete = usbd_otg->regs->endptcomplete;
|
|
usbd_flush_endpoint(USB_EP_ALL);
|
|
}
|
|
|
|
// Check if port change happened.
|
|
if (usb_status_irqs & USB2D_USBSTS_PCI)
|
|
usbd_otg->port_speed = (usbd_otg->regs->hostpc1_devlc & USB2D_HOSTPC1_DEVLC_PSPD_MASK) >> 25;
|
|
|
|
// Acknowledge setup request for EP0 and copy its configuration.
|
|
u32 ep0_setup_req = usbd_otg->regs->endptsetupstat;
|
|
if (ep0_setup_req & 1)
|
|
{
|
|
usbd_otg->regs->endptsetupstat = ep0_setup_req;
|
|
memcpy(&usbd_otg->control_setup, (void *)usbdaemon->qhs->setup, 8);
|
|
if (_usbd_handle_ep0_control_transfer())
|
|
break;
|
|
}
|
|
if (usbd_otg->configuration_set)
|
|
return USB_RES_OK;
|
|
|
|
if (timer < get_tmr_ms() || btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN))
|
|
return USB_ERROR_USER_ABORT;
|
|
}
|
|
}
|
|
|
|
return USB_ERROR_TIMEOUT;
|
|
}
|
|
|
|
int usb_device_enumerate(usb_gadget_type gadget)
|
|
{
|
|
switch (gadget)
|
|
{
|
|
case USB_GADGET_UMS:
|
|
usbd_otg->desc = &usb_gadget_ums_descriptors;
|
|
break;
|
|
case USB_GADGET_HID_GAMEPAD:
|
|
usbd_otg->desc = &usb_gadget_hid_jc_descriptors;
|
|
break;
|
|
case USB_GADGET_HID_TOUCHPAD:
|
|
usbd_otg->desc = &usb_gadget_hid_touch_descriptors;
|
|
break;
|
|
}
|
|
|
|
usbd_otg->gadget = gadget;
|
|
|
|
return _usbd_ep0_initialize();
|
|
}
|
|
|
|
int usbd_handle_ep0_ctrl_setup()
|
|
{
|
|
// Acknowledge setup request for EP0 and copy its configuration.
|
|
u32 ep0_setup_req = usbd_otg->regs->endptsetupstat;
|
|
if (ep0_setup_req & 1)
|
|
{
|
|
usbd_otg->regs->endptsetupstat = ep0_setup_req;
|
|
memcpy(&usbd_otg->control_setup, (void *)usbdaemon->qhs->setup, 8);
|
|
_usbd_handle_ep0_control_transfer();
|
|
memset(usb_ep0_ctrl_buf, 0, USB_TD_BUFFER_PAGE_SIZE);
|
|
}
|
|
|
|
// Only return error if bulk reset was requested.
|
|
if (usbd_otg->bulk_reset_req)
|
|
{
|
|
usbd_otg->bulk_reset_req = false;
|
|
return USB_RES_BULK_RESET;
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
static usb_ep_status_t _usbd_get_ep1_status(usb_dir_t dir)
|
|
{
|
|
usb_ep_t ep;
|
|
if (dir == USB_DIR_OUT)
|
|
ep = USB_EP_BULK_OUT;
|
|
else
|
|
ep = USB_EP_BULK_IN;
|
|
return _usbd_get_ep_status(ep);
|
|
}
|
|
|
|
int usb_device_ep1_out_read(u8 *buf, u32 len, u32 *bytes_read, bool sync)
|
|
{
|
|
if ((u32)buf % USB_EP_BUFFER_ALIGN)
|
|
return USB2_ERROR_XFER_NOT_ALIGNED;
|
|
|
|
if (len > USB_EP_BUFFER_MAX_SIZE)
|
|
len = USB_EP_BUFFER_MAX_SIZE;
|
|
|
|
int res = _usbd_ep_operation(USB_EP_BULK_OUT, buf, len, sync);
|
|
|
|
if (sync && bytes_read)
|
|
*bytes_read = res ? 0 : len;
|
|
|
|
return res;
|
|
}
|
|
|
|
int usb_device_ep1_out_read_big(u8 *buf, u32 len, u32 *bytes_read)
|
|
{
|
|
if ((u32)buf % USB_EP_BUFFER_ALIGN)
|
|
return USB2_ERROR_XFER_NOT_ALIGNED;
|
|
|
|
if (len > USB_EP_BULK_OUT_MAX_XFER)
|
|
len = USB_EP_BULK_OUT_MAX_XFER;
|
|
|
|
int res;
|
|
u32 bytes = 0;
|
|
*bytes_read = 0;
|
|
u8 *buf_curr = buf;
|
|
|
|
while (len)
|
|
{
|
|
u32 len_ep = MIN(len, USB_EP_BUFFER_MAX_SIZE);
|
|
|
|
res = usb_device_ep1_out_read(buf_curr, len_ep, &bytes, USB_XFER_SYNCED);
|
|
if (res)
|
|
return res;
|
|
|
|
len -= len_ep;
|
|
buf_curr += len_ep;
|
|
*bytes_read = *bytes_read + bytes;
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
static int _usbd_get_ep1_out_bytes_read()
|
|
{
|
|
if (_usbd_get_ep_status(USB_EP_BULK_OUT) != USB_EP_STATUS_IDLE)
|
|
return 0;
|
|
else
|
|
return (usbdaemon->ep_bytes_requested[USB_EP_BULK_OUT] - (usbdaemon->qhs[USB_EP_BULK_OUT].token >> 16));
|
|
}
|
|
|
|
int usb_device_ep1_out_reading_finish(u32 *pending_bytes, int tries)
|
|
{
|
|
usb_ep_status_t ep_status;
|
|
do
|
|
{
|
|
ep_status = _usbd_get_ep1_status(USB_DIR_OUT);
|
|
if ((ep_status == USB_EP_STATUS_IDLE) || (ep_status == USB_EP_STATUS_DISABLED))
|
|
break;
|
|
|
|
usbd_handle_ep0_ctrl_setup();
|
|
}
|
|
while ((ep_status == USB_EP_STATUS_ACTIVE) || (ep_status == USB_EP_STATUS_STALLED));
|
|
|
|
*pending_bytes = _usbd_get_ep1_out_bytes_read();
|
|
|
|
bpmp_mmu_maintenance(BPMP_MMU_MAINT_CLN_INV_WAY, false);
|
|
|
|
if (ep_status == USB_EP_STATUS_IDLE)
|
|
return USB_RES_OK;
|
|
else if (ep_status == USB_EP_STATUS_DISABLED)
|
|
return USB2_ERROR_XFER_EP_DISABLED;
|
|
else
|
|
return USB_ERROR_XFER_ERROR;
|
|
}
|
|
|
|
int usb_device_ep1_in_write(u8 *buf, u32 len, u32 *bytes_written, bool sync)
|
|
{
|
|
if ((u32)buf % USB_EP_BUFFER_ALIGN)
|
|
return USB2_ERROR_XFER_NOT_ALIGNED;
|
|
|
|
if (len > USB_EP_BUFFER_MAX_SIZE)
|
|
len = USB_EP_BUFFER_MAX_SIZE;
|
|
|
|
int res = _usbd_ep_operation(USB_EP_BULK_IN, buf, len, sync);
|
|
|
|
if (sync && bytes_written)
|
|
*bytes_written = res ? 0 : len;
|
|
|
|
return res;
|
|
}
|
|
|
|
static int _usbd_get_ep1_in_bytes_written()
|
|
{
|
|
if (_usbd_get_ep_status(USB_EP_BULK_IN) != USB_EP_STATUS_IDLE)
|
|
return 0;
|
|
else
|
|
return (usbdaemon->ep_bytes_requested[USB_EP_BULK_IN] - (usbdaemon->qhs[USB_EP_BULK_IN].token >> 16));
|
|
}
|
|
|
|
int usb_device_ep1_in_writing_finish(u32 *pending_bytes)
|
|
{
|
|
usb_ep_status_t ep_status;
|
|
do
|
|
{
|
|
ep_status = _usbd_get_ep1_status(USB_DIR_IN);
|
|
if ((ep_status == USB_EP_STATUS_IDLE) || (ep_status == USB_EP_STATUS_DISABLED))
|
|
break;
|
|
|
|
usbd_handle_ep0_ctrl_setup();
|
|
}
|
|
while ((ep_status == USB_EP_STATUS_ACTIVE) || (ep_status == USB_EP_STATUS_STALLED));
|
|
|
|
*pending_bytes = _usbd_get_ep1_in_bytes_written();
|
|
|
|
if (ep_status == USB_EP_STATUS_IDLE)
|
|
return USB_RES_OK;
|
|
else if (ep_status == USB_EP_STATUS_DISABLED)
|
|
return USB2_ERROR_XFER_EP_DISABLED;
|
|
|
|
usb_device_stall_ep1_bulk_out();
|
|
return USB_ERROR_XFER_ERROR;
|
|
}
|
|
|
|
bool usb_device_get_suspended()
|
|
{
|
|
bool suspended = (usbd_otg->regs->portsc1 & USB2D_PORTSC1_SUSP) == USB2D_PORTSC1_SUSP;
|
|
return suspended;
|
|
}
|
|
|
|
bool usb_device_get_port_in_sleep()
|
|
{
|
|
// Windows heuristic: Forces port into suspend, sleep and J-State.
|
|
return (usbd_otg->regs->portsc1) == 0x885;
|
|
}
|
|
|
|
int usb_device_class_send_max_lun(u8 max_lun)
|
|
{
|
|
// Timeout if get MAX_LUN request doesn't happen in 10s.
|
|
u32 timer = get_tmr_ms() + 10000;
|
|
|
|
usbd_otg->max_lun = max_lun;
|
|
|
|
while (!usbd_otg->max_lun_set)
|
|
{
|
|
usbd_handle_ep0_ctrl_setup();
|
|
if (timer < get_tmr_ms() || btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN))
|
|
return USB_ERROR_USER_ABORT;
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
int usb_device_class_send_hid_report()
|
|
{
|
|
// Timeout if get GET_HID_REPORT request doesn't happen in 10s.
|
|
u32 timer = get_tmr_ms() + 10000;
|
|
|
|
// Wait for request and transfer start.
|
|
while (!usbd_otg->hid_report_sent)
|
|
{
|
|
usbd_handle_ep0_ctrl_setup();
|
|
if (timer < get_tmr_ms() || btn_read_vol() == (BTN_VOL_UP | BTN_VOL_DOWN))
|
|
return USB_ERROR_USER_ABORT;
|
|
}
|
|
|
|
return USB_RES_OK;
|
|
}
|
|
|
|
void usb_device_get_ops(usb_ops_t *ops)
|
|
{
|
|
ops->usbd_flush_endpoint = usbd_flush_endpoint;
|
|
ops->usbd_set_ep_stall = usbd_set_ep_stall;
|
|
ops->usbd_handle_ep0_ctrl_setup = usbd_handle_ep0_ctrl_setup;
|
|
ops->usbd_end = usbd_end;
|
|
ops->usb_device_init = usb_device_init;
|
|
ops->usb_device_enumerate = usb_device_enumerate;
|
|
ops->usb_device_class_send_max_lun = usb_device_class_send_max_lun;
|
|
ops->usb_device_class_send_hid_report = usb_device_class_send_hid_report;
|
|
ops->usb_device_get_suspended = usb_device_get_suspended;
|
|
ops->usb_device_get_port_in_sleep = usb_device_get_port_in_sleep;
|
|
|
|
ops->usb_device_ep1_out_read = usb_device_ep1_out_read;
|
|
ops->usb_device_ep1_out_read_big = usb_device_ep1_out_read_big;
|
|
ops->usb_device_ep1_out_reading_finish = usb_device_ep1_out_reading_finish;
|
|
ops->usb_device_ep1_in_write = usb_device_ep1_in_write;
|
|
ops->usb_device_ep1_in_writing_finish = usb_device_ep1_in_writing_finish;
|
|
}
|
|
|