max7762x: Update everything to use the improved pmic management

This commit is contained in:
CTCaer 2021-01-04 02:41:15 +02:00
parent 0f9aa51afe
commit 745ac609d2
9 changed files with 54 additions and 78 deletions

View file

@ -229,19 +229,20 @@ void display_init()
if (!tegra_t210) if (!tegra_t210)
{ {
// Set SD2 regulator voltage. // Set SD2 regulator voltage.
max77620_regulator_set_voltage(REGULATOR_SD2, 1325000); max7762x_regulator_set_voltage(REGULATOR_SD2, 1325000);
// Set slew rate and enable SD2 regulator. // Set slew rate and enable SD2 regulator.
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_SD2_CFG, (1 << MAX77620_SD_SR_SHIFT) | MAX77620_SD_CFG1_FSRADE_SD_ENABLE); i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_SD2_CFG, (1 << MAX77620_SD_SR_SHIFT) | MAX77620_SD_CFG1_FSRADE_SD_ENABLE);
max77620_regulator_enable(REGULATOR_SD2, 1); max7762x_regulator_enable(REGULATOR_SD2, true);
} }
// Enable power to display panel controller. // Enable power to display panel controller.
max77620_regulator_set_volt_and_flags(REGULATOR_LDO0, 1200000, MAX77620_POWER_MODE_NORMAL); // Configure to 1.2V. max7762x_regulator_set_voltage(REGULATOR_LDO0, 1200000);
max7762x_regulator_enable(REGULATOR_LDO0, true);
if (tegra_t210) if (tegra_t210)
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_GPIO7, max77620_config_gpio(7, MAX77620_GPIO_OUTPUT_ENABLE); // T210: LD0 -> GPIO7 -> Display panel.
MAX77620_CNFG_GPIO_OUTPUT_VAL_HIGH | MAX77620_CNFG_GPIO_DRV_PUSHPULL); // T210: LD0 -> GPIO7 -> Display panel.
// Enable Display Interface specific clocks. // Enable Display Interface specific clocks.
CLOCK(CLK_RST_CONTROLLER_RST_DEV_H_CLR) = BIT(CLK_H_MIPI_CAL) | BIT(CLK_H_DSI); CLOCK(CLK_RST_CONTROLLER_RST_DEV_H_CLR) = BIT(CLK_H_MIPI_CAL) | BIT(CLK_H_DSI);

View file

@ -17,7 +17,7 @@
*/ */
#include "als.h" #include "als.h"
#include <power/max77620.h> #include <power/max7762x.h>
#include <soc/clock.h> #include <soc/clock.h>
#include <soc/i2c.h> #include <soc/i2c.h>
#include <soc/pinmux.h> #include <soc/pinmux.h>
@ -97,14 +97,16 @@ void get_als_lux(als_table_t *als_val)
u8 als_init(als_table_t *als_val) u8 als_init(als_table_t *als_val)
{ {
// Enable power to ALS IC.
max7762x_regulator_set_voltage(REGULATOR_LDO6, 2900000);
max7762x_regulator_enable(REGULATOR_LDO6, true);
// Init I2C2.
pinmux_config_i2c(I2C_2); pinmux_config_i2c(I2C_2);
clock_enable_i2c(I2C_2); clock_enable_i2c(I2C_2);
i2c_init(I2C_2); i2c_init(I2C_2);
max77620_regulator_set_volt_and_flags(REGULATOR_LDO6, 2900000, MAX77620_POWER_MODE_NORMAL); // Initialize ALS.
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_LDO6_CFG2,
(MAX77620_POWER_MODE_NORMAL << MAX77620_LDO_POWER_MODE_SHIFT | (3 << 3) | MAX77620_LDO_CFG2_ADE_ENABLE));
u8 id = i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(0x12)); u8 id = i2c_recv_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(0x12));
i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_SPEC(BH1730_SPECCMD_RESET), 0); i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_SPEC(BH1730_SPECCMD_RESET), 0);
i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_GAIN_REG), HOS_GAIN); i2c_send_byte(I2C_2, BH1730_I2C_ADDR, BH1730_ADDR(BH1730_GAIN_REG), HOS_GAIN);

View file

@ -23,7 +23,6 @@
#include <soc/i2c.h> #include <soc/i2c.h>
#include <soc/pinmux.h> #include <soc/pinmux.h>
#include <power/max7762x.h> #include <power/max7762x.h>
#include <power/max77620.h>
#include <soc/gpio.h> #include <soc/gpio.h>
#include <soc/t210.h> #include <soc/t210.h>
#include <utils/btn.h> #include <utils/btn.h>
@ -358,10 +357,9 @@ static int touch_init()
int touch_power_on() int touch_power_on()
{ {
// Enables LDO6 for touchscreen VDD/AVDD supply // Enable LDO6 for touchscreen VDD/AVDD supply.
max77620_regulator_set_volt_and_flags(REGULATOR_LDO6, 2900000, MAX77620_POWER_MODE_NORMAL); max7762x_regulator_set_voltage(REGULATOR_LDO6, 2900000);
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_LDO6_CFG2, max7762x_regulator_enable(REGULATOR_LDO6, true);
(MAX77620_POWER_MODE_NORMAL << MAX77620_LDO_POWER_MODE_SHIFT | (3 << 3) | MAX77620_LDO_CFG2_ADE_ENABLE));
// Configure touchscreen GPIO. // Configure touchscreen GPIO.
PINMUX_AUX(PINMUX_AUX_DAP4_SCLK) = PINMUX_PULL_DOWN | 1; PINMUX_AUX(PINMUX_AUX_DAP4_SCLK) = PINMUX_PULL_DOWN | 1;
@ -414,9 +412,7 @@ void touch_power_off()
gpio_write(GPIO_PORT_J, GPIO_PIN_7, GPIO_LOW); gpio_write(GPIO_PORT_J, GPIO_PIN_7, GPIO_LOW);
// Disables LDO6 for touchscreen VDD, AVDD supply // Disables LDO6 for touchscreen VDD, AVDD supply
max77620_regulator_enable(REGULATOR_LDO6, 0); max7762x_regulator_enable(REGULATOR_LDO6, false);
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_LDO6_CFG2,
MAX77620_LDO_CFG2_ADE_ENABLE | (2 << 3) | (MAX77620_POWER_MODE_NORMAL << MAX77620_LDO_POWER_MODE_SHIFT));
clock_disable_i2c(I2C_3); clock_disable_i2c(I2C_3);
} }

View file

@ -1485,7 +1485,7 @@ static void _sdram_init_t210()
const sdram_params_t210_t *params = (const sdram_params_t210_t *)_sdram_get_params_t210(); const sdram_params_t210_t *params = (const sdram_params_t210_t *)_sdram_get_params_t210();
// Set DRAM voltage. // Set DRAM voltage.
max77620_regulator_set_voltage(REGULATOR_SD1, 1100000); max7762x_regulator_set_voltage(REGULATOR_SD1, 1100000);
// VDDP Select. // VDDP Select.
PMC(APBDEV_PMC_VDDP_SEL) = params->pmc_vddp_sel; PMC(APBDEV_PMC_VDDP_SEL) = params->pmc_vddp_sel;
@ -1530,8 +1530,8 @@ static void _sdram_init_t210b01()
void sdram_init() void sdram_init()
{ {
// Configure SD regulator for DRAM. // Disable remote sense for SD1.
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_SD_CFG2, 0x05); i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_SD_CFG2, MAX77620_SD_CNF2_ROVS_EN_SD0 | MAX77620_SD_CNF2_RSVD);
if (hw_get_chip_id() == GP_HIDREV_MAJOR_T210) if (hw_get_chip_id() == GP_HIDREV_MAJOR_T210)
_sdram_init_t210(); _sdram_init_t210();

View file

@ -16,7 +16,6 @@
*/ */
#include <soc/ccplex.h> #include <soc/ccplex.h>
#include <soc/fuse.h>
#include <soc/hw_init.h> #include <soc/hw_init.h>
#include <soc/i2c.h> #include <soc/i2c.h>
#include <soc/clock.h> #include <soc/clock.h>
@ -29,27 +28,24 @@
void _ccplex_enable_power_t210() void _ccplex_enable_power_t210()
{ {
u8 tmp = i2c_recv_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_AME_GPIO); // Get current pinmuxing // Configure GPIO5 and enable output in order to power CPU pmic.
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_AME_GPIO, tmp & ~BIT(5)); // Disable GPIO5 pinmuxing. max77620_config_gpio(5, MAX77620_GPIO_OUTPUT_ENABLE);
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_GPIO5, MAX77620_CNFG_GPIO_DRV_PUSHPULL | MAX77620_CNFG_GPIO_OUTPUT_VAL_HIGH);
// Enable cores power. // Configure CPU pmic.
// 1-3.x: MAX77621_NFSR_ENABLE. // 1-3.x: MAX77621_NFSR_ENABLE.
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_CONTROL1_REG,
MAX77621_AD_ENABLE | MAX77621_NFSR_ENABLE | MAX77621_SNS_ENABLE | MAX77621_RAMP_12mV_PER_US);
// 1.0.0-3.x: MAX77621_T_JUNCTION_120 | MAX77621_CKKADV_TRIP_DISABLE | MAX77621_INDUCTOR_NOMINAL. // 1.0.0-3.x: MAX77621_T_JUNCTION_120 | MAX77621_CKKADV_TRIP_DISABLE | MAX77621_INDUCTOR_NOMINAL.
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_CONTROL2_REG, max77621_config_default(REGULATOR_CPU0, MAX77621_CTRL_HOS_CFG);
MAX77621_T_JUNCTION_120 | MAX77621_WDTMR_ENABLE | MAX77621_CKKADV_TRIP_75mV_PER_US| MAX77621_INDUCTOR_NOMINAL);
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_VOUT_REG, MAX77621_VOUT_ENABLE | MAX77621_VOUT_0_95V); // Set voltage and enable cores power.
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_VOUT_DVS_REG, MAX77621_VOUT_ENABLE | MAX77621_VOUT_0_95V); max7762x_regulator_set_voltage(REGULATOR_CPU0, 950000);
max7762x_regulator_enable(REGULATOR_CPU0, true);
} }
void _ccplex_enable_power_t210b01() void _ccplex_enable_power_t210b01()
{ {
u8 pmic_cpu_addr = !(FUSE(FUSE_RESERVED_ODM28_T210B01) & 1) ? MAX77812_PHASE31_CPU_I2C_ADDR : MAX77812_PHASE211_CPU_I2C_ADDR; // Set voltage and enable cores power.
u8 tmp = i2c_recv_byte(I2C_5, pmic_cpu_addr, MAX77812_REG_EN_CTRL); max7762x_regulator_set_voltage(REGULATOR_CPU1, 800000);
i2c_send_byte(I2C_5, pmic_cpu_addr, MAX77812_REG_EN_CTRL, tmp | MAX77812_EN_CTRL_EN_M4); max7762x_regulator_enable(REGULATOR_CPU1, true);
i2c_send_byte(I2C_5, pmic_cpu_addr, MAX77812_REG_M4_VOUT, MAX77812_M4_VOUT_0_80V);
} }
void ccplex_boot_cpu0(u32 entry) void ccplex_boot_cpu0(u32 entry)

View file

@ -287,19 +287,19 @@ static void _config_regulators(bool tegra_t210)
{ {
// Set RTC/AO domain to POR voltage. // Set RTC/AO domain to POR voltage.
if (tegra_t210) if (tegra_t210)
max77620_regulator_set_voltage(REGULATOR_LDO4, 1000000); max7762x_regulator_set_voltage(REGULATOR_LDO4, 1000000);
// Disable low battery shutdown monitor. // Disable low battery shutdown monitor.
max77620_low_battery_monitor_config(false); max77620_low_battery_monitor_config(false);
// Disable SDMMC1 IO power. // Disable SDMMC1 IO power.
gpio_write(GPIO_PORT_E, GPIO_PIN_4, GPIO_LOW); gpio_write(GPIO_PORT_E, GPIO_PIN_4, GPIO_LOW);
max77620_regulator_enable(REGULATOR_LDO2, 0); max7762x_regulator_enable(REGULATOR_LDO2, false);
sd_power_cycle_time_start = get_tmr_ms(); sd_power_cycle_time_start = get_tmr_ms();
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_CNFGBBC, MAX77620_CNFGBBC_RESISTOR_1K); i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_CNFGBBC, MAX77620_CNFGBBC_RESISTOR_1K);
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_ONOFFCNFG1, i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_ONOFFCNFG1,
BIT(6) | (3 << MAX77620_ONOFFCNFG1_MRT_SHIFT)); // PWR delay for forced shutdown off. MAX77620_ONOFFCNFG1_RSVD | (3 << MAX77620_ONOFFCNFG1_MRT_SHIFT)); // PWR delay for forced shutdown off.
if (tegra_t210) if (tegra_t210)
{ {
@ -317,28 +317,18 @@ static void _config_regulators(bool tegra_t210)
(4 << MAX77620_FPS_TIME_PERIOD_SHIFT) | (2 << MAX77620_FPS_PD_PERIOD_SHIFT)); // 3.x+ (4 << MAX77620_FPS_TIME_PERIOD_SHIFT) | (2 << MAX77620_FPS_PD_PERIOD_SHIFT)); // 3.x+
// Set vdd_core voltage to 1.125V. // Set vdd_core voltage to 1.125V.
max77620_regulator_set_voltage(REGULATOR_SD0, 1125000); max7762x_regulator_set_voltage(REGULATOR_SD0, 1125000);
// Fix CPU/GPU after a L4T warmboot. // Fix CPU/GPU after L4T warmboot.
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_GPIO5, 2); max77620_config_gpio(5, MAX77620_GPIO_OUTPUT_DISABLE);
i2c_send_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_GPIO6, 2); max77620_config_gpio(6, MAX77620_GPIO_OUTPUT_DISABLE);
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_VOUT_REG, MAX77621_VOUT_0_95V); // Disable power. // Set POR configuration.
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_VOUT_DVS_REG, MAX77621_VOUT_ENABLE | MAX77621_VOUT_1_09V); // Enable DVS power. max77621_config_default(REGULATOR_CPU0, MAX77621_CTRL_POR_CFG);
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_CONTROL1_REG, MAX77621_RAMP_50mV_PER_US); max77621_config_default(REGULATOR_GPU0, MAX77621_CTRL_POR_CFG);
i2c_send_byte(I2C_5, MAX77621_CPU_I2C_ADDR, MAX77621_CONTROL2_REG,
MAX77621_T_JUNCTION_120 | MAX77621_FT_ENABLE | MAX77621_CKKADV_TRIP_75mV_PER_US_HIST_DIS |
MAX77621_CKKADV_TRIP_150mV_PER_US | MAX77621_INDUCTOR_NOMINAL);
i2c_send_byte(I2C_5, MAX77621_GPU_I2C_ADDR, MAX77621_VOUT_REG, MAX77621_VOUT_0_95V); // Disable power.
i2c_send_byte(I2C_5, MAX77621_GPU_I2C_ADDR, MAX77621_VOUT_DVS_REG, MAX77621_VOUT_ENABLE | MAX77621_VOUT_1_09V); // Enable DVS power.
i2c_send_byte(I2C_5, MAX77621_GPU_I2C_ADDR, MAX77621_CONTROL1_REG, MAX77621_RAMP_50mV_PER_US);
i2c_send_byte(I2C_5, MAX77621_GPU_I2C_ADDR, MAX77621_CONTROL2_REG,
MAX77621_T_JUNCTION_120 | MAX77621_FT_ENABLE | MAX77621_CKKADV_TRIP_75mV_PER_US_HIST_DIS |
MAX77621_CKKADV_TRIP_150mV_PER_US | MAX77621_INDUCTOR_NOMINAL);
} }
else // Tegra X1+ set vdd_core voltage to 1.05V. else // Tegra X1+ set vdd_core voltage to 1.05V.
max77620_regulator_set_voltage(REGULATOR_SD0, 1050000); max7762x_regulator_set_voltage(REGULATOR_SD0, 1050000);
} }
void hw_init() void hw_init()
@ -396,7 +386,10 @@ void hw_init()
//! TODO: Why? Device is NFC MCU on Lite. //! TODO: Why? Device is NFC MCU on Lite.
if (nx_hoag) if (nx_hoag)
max77620_regulator_set_volt_and_flags(REGULATOR_LDO8, 2800000, MAX77620_POWER_MODE_NORMAL); {
max7762x_regulator_set_voltage(REGULATOR_LDO8, 2800000);
max7762x_regulator_enable(REGULATOR_LDO8, true);
}
// Initialize I2C1 for various power related devices. // Initialize I2C1 for various power related devices.
i2c_init(I2C_1); i2c_init(I2C_1);

View file

@ -1200,8 +1200,8 @@ static int _sdmmc_config_sdmmc1(bool t210b01)
usleep(10000); usleep(10000);
// Enable SD card IO power. // Enable SD card IO power.
max77620_regulator_set_voltage(REGULATOR_LDO2, 3300000); max7762x_regulator_set_voltage(REGULATOR_LDO2, 3300000);
max77620_regulator_enable(REGULATOR_LDO2, 1); max7762x_regulator_enable(REGULATOR_LDO2, true);
usleep(1000); usleep(1000);
// Set pad slew codes to get good quality clock. // Set pad slew codes to get good quality clock.
@ -1332,19 +1332,6 @@ int sdmmc_init(sdmmc_t *sdmmc, u32 id, u32 power, u32 bus_width, u32 type, int p
void sdmmc1_disable_power() void sdmmc1_disable_power()
{ {
#if 0
// Ensure regulator is into default voltage.
if (PMC(APBDEV_PMC_PWR_DET_VAL) & PMC_PWR_DET_SDMMC1_IO_EN)
{
// Switch to 1.8V and wait for regulator to stabilize.
max77620_regulator_set_voltage(REGULATOR_LDO2, 1800000);
usleep(150);
// Inform IO pads that we switched to 1.8V.
PMC(APBDEV_PMC_PWR_DET_VAL) &= ~(PMC_PWR_DET_SDMMC1_IO_EN);
(void)PMC(APBDEV_PMC_PWR_DET_VAL); // Commit write.
}
#endif
// T210B01 WAR: Clear pull down from CLK pad. // T210B01 WAR: Clear pull down from CLK pad.
PINMUX_AUX(PINMUX_AUX_SDMMC1_CLK) &= ~PINMUX_PULL_MASK; PINMUX_AUX(PINMUX_AUX_SDMMC1_CLK) &= ~PINMUX_PULL_MASK;
@ -1352,7 +1339,7 @@ void sdmmc1_disable_power()
_sdmmc_config_sdmmc1_pads(true); _sdmmc_config_sdmmc1_pads(true);
// Disable SD card IO power regulator. // Disable SD card IO power regulator.
max77620_regulator_enable(REGULATOR_LDO2, 0); max7762x_regulator_enable(REGULATOR_LDO2, false);
usleep(4000); usleep(4000);
// Disable SD card IO power pin. // Disable SD card IO power pin.
@ -1441,7 +1428,7 @@ int sdmmc_enable_low_voltage(sdmmc_t *sdmmc)
_sdmmc_commit_changes(sdmmc); _sdmmc_commit_changes(sdmmc);
// Switch to 1.8V and wait for regulator to stabilize. Assume max possible wait needed. // Switch to 1.8V and wait for regulator to stabilize. Assume max possible wait needed.
max77620_regulator_set_voltage(REGULATOR_LDO2, 1800000); max7762x_regulator_set_voltage(REGULATOR_LDO2, 1800000);
usleep(150); usleep(150);
// Inform IO pads that we switched to 1.8V. // Inform IO pads that we switched to 1.8V.

View file

@ -29,7 +29,7 @@ u8 btn_read()
res |= BTN_VOL_DOWN; res |= BTN_VOL_DOWN;
if (!gpio_read(GPIO_PORT_X, GPIO_PIN_6)) if (!gpio_read(GPIO_PORT_X, GPIO_PIN_6))
res |= BTN_VOL_UP; res |= BTN_VOL_UP;
if (i2c_recv_byte(4, MAX77620_I2C_ADDR, MAX77620_REG_ONOFFSTAT) & 0x4) if (i2c_recv_byte(4, MAX77620_I2C_ADDR, MAX77620_REG_ONOFFSTAT) & MAX77620_ONOFFSTAT_EN0)
res |= BTN_POWER; res |= BTN_POWER;
return res; return res;
} }

View file

@ -164,7 +164,8 @@ void power_set_state(power_state_t state)
case POWER_OFF_RESET: case POWER_OFF_RESET:
case POWER_OFF_REBOOT: case POWER_OFF_REBOOT:
// Disable soft reset wake event. default:
// Enable/Disable soft reset wake event.
reg = i2c_recv_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_ONOFFCNFG2); reg = i2c_recv_byte(I2C_5, MAX77620_I2C_ADDR, MAX77620_REG_ONOFFCNFG2);
if (state == POWER_OFF_RESET) if (state == POWER_OFF_RESET)
reg &= ~MAX77620_ONOFFCNFG2_SFT_RST_WK; // Do not wake up after power off. reg &= ~MAX77620_ONOFFCNFG2_SFT_RST_WK; // Do not wake up after power off.